Cart Cart
Steinbach Steinbach

Sand filter systems

040310
Art.
  • Powerful filter unit for pools up to 22,000 l capacity
  • Connectors for all common pools Ø 32/38 mm
  • 7 way valve with adjustment lever and pressure gauge
  • Comprehensive range of accessories available
X

Sold Out

The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.

Notifiy me:

€199.00
inclusive of VAT

The Steinbach filter unit Classic 310 has a circulation capacity of 4.500 l/h, the connection is 230 V/250 W. This filter unit can be used for pools with approx. 22.000 l water content be connected to all commercially available installation pools with a hose connection Ø 32/38 mm. The filter unit can be used up to a maximum water temperature of 35 ° C. To maintain crystal-clear and sparkling pool water, the filter system can be operated with filter sand as well as with Steinbach Filter Balls as filter medium.

 

Technical data:

  • Filter pump 040921
  • Circulation power 4,500 l/h
  • Self-priming pump with pre-filter
  • Maximum water temperature 35 °C
  • 230 V/250 W
  • 7 way valve with pressure gauge
  • Tank Ø 320 mm
  • Connector Ø 32/38 mm
  • Ground plate
  • For pools up to 22,000 l capacity
  • Available separately: Steinbach Container for Steinbach UV-disinfection system

Usable filter media:

  • Original Steinbach Filter Balls
  • Filter sand approx. 20 kg grain size 0.70-1.20 mm
integrierte Zeitschaltuhr:-
selbstsaugende Pumpe:X
Vorfilter:X
Leistung in Watt:250
Ventil:7 - Wege
Anschluss in Volt:230
Schlauchanschluss:Ø 32/38 mm
TX-SPEED-CLASSIC_02.jpg

7-way valve

The massive 7-way valve allows you to adjust the various operations of your filter unit: Filtering, backwashing, rinsing, circulating, draining, winter setting and closed. The 7-way valve allows you to carry out the complete water cleaning process.

TX-SPEED-CLASSIC_07.jpg

Integrated pressure gauge

The pressure gauge built into the 7-way Venit not only shows you the current operating pressure of your filter unit, but also the condition of the filter medium in your system. The scale of the manometer is divided into 3 areas.

 

GREEN = filtration perfect

YELLOW = RINSE the unit or wash the filter medium if Steinbach Filter Balls are used

RED = Immediately backwash the unit or, if Steinbach Filter Balls are used, wash the filter medium or (if necessary, replace the filter medium)

TX-SPEED-CLASSIC_01.jpg

Standard connection

The models Steinbach filter unit Classic Series have connections for swimming pool hoses with Ø 32/38 mm. This allows you to connect the filter units quickly and easily to almost all commercial swimming pools on the market.

TX-SPEED-CLASSIC_03.jpg

High quality and powerful filter pump

The filter pumps are the power station of every pool circuit. The filter pumps of the Steinbach filter units Classic series have a high filter performance with low power consumption. The filter pumps are perfectly matched to the respective filter units and ensure that your pool water is perfectly filtered.

TX-SPEED-CLASSIC_06.JPG

Transparent inspection window for the filter cleaning process

Every filter unit must be cleaned at regular intervals using the backwash and rinse procedure. But it is not actually very easy to check accurately whether the filter sand has been cleaned adequately. We have the answer to this for you in the inspection window, which is built into the 7 way valve. Now you can make a visual check of the water flowing out of the filter unit towards the pipe. This facilitates efficient and above all water saving cleaning.

TX-SPEED-CLASSIC_07.JPG

Pressure control

A pressure gauge built into the 7 way valve doesn’t just show you the current operational pressure in your sand filter unit, it also shows the status of the filtration medium. The scale is divided into three sections.


GREEN = perfect filtration

AMBER = BACKWASH the unit soon (clean the filter sand)

RED = BACKWASH the unit immediately, filtration no longer guaranteed.

01
7-Wege-Ventil Classic-Serie
Required quantity for your set: 1
02
Entlüftungsschraube (inkl. Dichtung)
Required quantity for your set: 1
03
Dichtung Ventilkopf
Required quantity for your set: 1
04
O-Ring zwischen 7-Wege-Ventil/Kessel
Required quantity for your set: 1
06
Spannring (inkl. Verschraubung)
Required quantity for your set: 1
07
Steigrohr für Kessel
Required quantity for your set: 1
08
Zentrierer
Required quantity for your set: 1
09
Mittelstück für Filterarme
Required quantity for your set: 1
10
Filterarm
Required quantity for your set: 6
11
Entleerungsschrauben-Set
Required quantity for your set: 1
12
Kessel Ø 320 mm
Required quantity for your set: 1
13
Grundplatte
Required quantity for your set: 1
14
Verbindungsschlauch, L = 30 cm, Ø 38 mm
Required quantity for your set: 1
15
Schlauchschelle Ø 30 - 50 mm
Required quantity for your set: 1
16
Manometer
Required quantity for your set: 1
17
Steinbach Filter pump SPS 50-1
Required quantity for your set: 1
18
Pumpenadapter Ø 32/38 mm x 1 1/2" AG
Required quantity for your set: 1
Befestigungsset für Filterpumpen
Required quantity for your set: 1

FAQs from category Sand filter systems:

Should the filter system run during bathing?

No, the filter system may only run when the pool is not in use. On the one hand, there is a risk of injury from the suction nozzle, on the other hand, dirt particles are swirled around during use, which the system cannot filter. 

How long should my filter system be running?

The filter system should circulate your pool water at least twice a day. Our Comfort 75 filter system, for example, manages approx. 8,000 litres per hour and can therefore completely circulate a pool with 19,000 litres once in just under 2.5 hours.

The lights on my timer are red, does this mean an error message?

No, the red lights are not an error message. The lights on the timer are alternately green and red.

The external timer does not work on my Intex sand filter system, what can I do?

With Intex sand filter systems, only the integrated timer works; an external timer cannot be connected due to the safety standards.

The time set on the external timer does not work, what can I do?

Remove the transport lock from the button cell battery. If you do not remove these, the filter times will not be saved in the event of a power failure. Check the battery and replace it if necessary. (Button cell lithium 3V CR2032)  not work, what can I do?

How do I use an external timer?

Remove the transport lock from the button cell battery. Set the external timer at the desired times and then plug the pump into the timer. Now start the integrated timer of the pump and set the time to 24 hours. The pump then starts at the times set on the external timer.

The timer does not switch on the unit at the desired time despite being set correctly, what can I do?

Remove the transport lock from the button cell battery. Check the battery and replace it if necessary.

Why do I have to switch off the filter pump before I operate the way valve?

If you open the lever of the way valve valve during operation, the water will flow with pressure from all openings. The pressure drop may cause damage to the unit.

The pump makes noises like grinding or humming, what can I do?

Rust may have accumulated over the winter, which prevents the pump from starting or makes grinding noises when it is switched on. If the rust build-up is not too bad, this fault can be easily remedied. On most pumps, there is a small recess in the cover for ventilation, behind which there is a screw. Use a screwdriver to loosen the screw slightly and spray it with lubricant (e.g. WD40). If the rust has not settled too much, the pump will work again.

The pump cannot be activated, what can I do?

Check your socket for power and test another socket if necessary. Never run the pump without water, the pump may run dry and burn out. Check the mains plug or the connection cable for damage. Check the running time of the external timer. Check the running time of the timer, if it is set.

How often do I have to change the filter sand?

Depending on the grain size, the filter sand must be changed after three to five seasons.

The pressure in the vessel is too high or low, what can I do?

If the pressure in the boiler is too high, you must clean the filter bed (sand in the boiler) by backwashing. If filter balls are used, check them regularly for the degree of contamination and remove them from the vessel at regular intervals and wash them out. Clean the filter balls with a garden hose or in the bathtub. DO NOT BACKWASH WHEN USING FILTER BALLS! If the pressure in the vessel is too low, you must check the pre-filter for dirt and clean it so that sufficient water can flow into the pump. Check the water level and the height of the hanging skimmer; if the water level is too low, too little water will flow into the pump. Check the pressure gauge for damage. Clean the pressure line and empty the pre-filter basket. It could be that the suction line or the pre-filter basket are blocked. If the operating mode is set to "CLOSED", use another operating mode. It could be that the drain nozzle is closed. If this is the case, open it.

There is air in the sand filter system, what can I do?

Fill the pump with water, loosen the transparent cover on the filter container (do not unscrew completely) to remove trapped air. Tighten the cover again when all air has escaped. Check all connections and hoses for leaks or holes. Retighten connections or hose clamps, seal with Teflon tape and replace the defective parts if necessary.

There is sand in the pool (e.g.: after initial filling or refilling), what can I do?

When filling the vessel with sand, check that the sieve bottom and the separating plate are correctly inserted. Before filling sand into the vessel, add approx. 20-30 cm of water to the vessel and fill the sand slowly to avoid damage due to the weight of the sand. Before the first filtering process, you must filter out the undersize particles of the sand. To do this, backwash for several minutes until clear water comes out of the backwash connection. If the sieve bottom or the separating plate are damaged, replace them. Please also observe the instructions for your filter system.

The clamping ring does not close properly, what can I do?

It is best to close the clamping ring with the help of a second person. A screw clamp can be used as an aid. The clamping ring must be tapped over the skeleton of the valve cover and vessel. If tapping with the palm of the hand is not enough, a rubber mallet can also be used. Start tapping at the back of the bolt and hit the tension ring evenly on the right and left until the ribbed pattern disappears. Then the clamping ring can also be easily closed with the bolt. The closure requires some force and must be a little stronger, as the vessel builds up pressure when used and must seal 100%. Do not use an ordinary hammer under any circumstances. Damage caused by this is not covered by the warranty or guarantee.

The boiler is leaking, what can I do?

Check whether the seal (O-ring) is inserted correctly. If it is not placed with the nose in the groove of the vessel, the 7-way valve does not close properly and there is a higher distance between the 7-way valve and the vessel. Check whether the partition in the sand and clean water chamber area is correctly inserted in the sieve bottom. If not, the 7-way valve is also too high. Make sure that the seal at the top of the filter tank is in clean and perfect condition and that no sand is sticking to it. You can coat the O-ring with Vaseline. This serves to preserve the O-ring and additionally supports the sealing. Check that the 7-way valve is correctly fitted with the notch on the underside of the cover and the notch on the filter. Place the 7-way valve on the filter vessel, preferably with the help of a second person. Press the lid onto the filter bowl and make sure that the lid is flush with the vessel.

! Important information

Symbolic photos - The pictures shown are for reference only, the actual product may vary.