- Fully automatic floor vacuum cleaner for optimum floor and wall cleaning
- Special floor, wall and combi cleaning modi
- Remote control via app possible (Android + iOS)
- Integrated filter system, capacity approx. 20.000 l/h
- "Weekly Timer" for individually settable cleaning periods
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Fully automated, electric Poolrunner APPcontrol for all pools with a flat floor. Special plastic brushes clean both the floor and the walls. With an integrated filter unit combined with a 20.000 l/h performance pump, connection to an external filter system is not required. The pool cleaner can be controlled fully automatic or manual and can be controlled through an App (available for iOS and Android). The "Weekly Timer" can be used to define the time interval at which cleaning should start. The cable connecting the pool cleaner and control unit is approximately 18,00 m long. Pools up to 50 m² can be easily cleaned.
No suitability for overflow-, stainless steel-, tile pools, as well as pools with an air ring. Please note that for pools with an installed ladder the wall cleaning mode is not possible.
Steinbach APPcontrol - Smartphone APPs
It is possible to control the APPcontrol via APP.
Please make sure that you install the correct APP for your swimming pool robot control unit on your smartphone.
For control units (article number 061969) until 2019 you have to download the "speedcleaner" APP. For control units (article number 061969A) from 2020 you have to download the new APP "Steinbach APPcontrol".
Please note the different designs of the control units for further assistance. The designs show you which APP has to be downloaded.
Please also make sure that you have the latest version of your operating system installed on your Android device or IOS device, so that the installation of the APP can be completed successfully.
Operating mode: App control, Control unit with cable, automatic, manual cleaning
Cleaning area: floor cleaning, wall cleaning, waterline
Suitable for saltwater: yes
Pump capacity: 20.000 l/h
Width of cleaning element: 361 mm
Speed: 12 m/min
Immersion depth: 2,00 m
Filter mesh: 75 μm
Safety class: IPX8
Water temperature: 10°C - 35°C
Ambient temperature: 10°C - 40°C
Pool size - floor area: 50 m²
App control: yes
Connection type: Bluetooth
App name (APP store): Steinbach APPcontrol
Transmission frequency: 2.402 - 2.480 MHz
Effective radiated power ERP: 4 dBM
Cable length to the device: 18,00 m
Control unit rated power: 200 W
Control unit energy power: 220-240V~ / 50Hz
Control unit output voltage: 24 V
Control unit safety class: IPX5
FAQs for Poolrunner APPcontrol:
For PVC liners, this pool robot can build up enough grip and the pool robot is therefore suitable for PVC liner. However, it should be noted that the diameter of the round pool is not too small, because the pool robot is relatively wide. In a pool with a smaller diameter (about 3.50 meters), the curvature is stronger and the pool vacuum cleaner does not adhere strongly enough.
FAQs from category Pool robots:
Do not leave the cable in the pool all the time. After each use, remove it from the pool and unplug and turn off the cord. Wash the cable with clean water to remove chemical residues after each cleaning operation. Put the cable length into the pool according to pool dimensions, place the remaining cable at the pool edge, i.e. pull overflown cable out of the water. Place obstacles such as built-in pool ladders/installation ladders out of the pool to prevent the cable from getting caught.
Position the power supply so that the cleaner can easily reach all areas. Switch off the filter pump while cleaning with the pool vacuum. Enter the maximum possible length of the connection cable in the pool, but take into account a corresponding minimum distance between the control unit and the pool. Change the setting of the nozzles.
Clean the filter container/filter bag and remove slippery debris such as algae from the pool walls. Put the pool vacuum cleaner into the pool at the optimum water temperature. This is between 10°C and 35°C. Check the drive belts and brushes for wear and replace them if necessary. Set the PH value correctly. This should be between 7.0 and 7.2. Switch off the unit and let all the air escape. Mount the additional buoyancy aids from the scope of delivery.
Check the plug of the power cord and the control unit or the battery. Plug the control unit directly into a socket and do not use extension cables. Check your house line for overload, the socket may be defective. Contact a qualified electrician.
There is air in the pool vacuum, switch off the unit, let all the air escape and let the pool vacuum sink to the ground. If necessary, adjust the salt content correctly.
Check the wheels/drive belts for wear and foreign objects in the drive. Replace the wheels/drive belts if necessary.
Check whether the water level in the pool is too high and drain the water if necessary. If your pool liner is a little rough, the pool vacuum will have more grip. Carry out a reduction of the buoyancy. If you have a salt water pool, the buoyancy is slightly higher in salt water; reduce the buoyancy.
It is necessary to weigh down the pool vacuum cleaner. A weight must be installed for this purpose. Please contact our Service Centre.
Our pool vacuums were designed for liner pools, the above materials have no grip or adhesion for the pool vacuum because the surfaces are too smooth.
Pull the cleaning hose and lift the automatic vacuum pool cleaner from the pool floor. The pool floor may be wrinkled, preventing the vacuum cleaner from moving. Check the water flow and make sure that the filter pump is switched on and has the appropriate power. Make sure that the gate valves are open. Clean or change the filter cartridge. For sand filter systems, you must backwash the filter.
You need to unblock or remove the cleaning lips because the sail, water outlet nozzle or cleaning lip may be stuck.
The buoyancy aids must be glued onto the inside of the upper part of the device - ideally offset and not directly next to each other.
The pool robot beeps when the ON/OFF button is pressed outside the water. This is due to the integrated water sensor. Put the pool robot into the water and after 15 seconds it will start cleaning the pool.
Press the ON/OFF button on the underside of the pool robot until you feel it click into place. If the ON/OFF button is pressed outside the water, the device beeps and does not switch on due to the integrated water sensor. Place the pool robot in the water. Please note: The pool robot only starts cleaning 15 seconds after it has been placed in the water.
All pool robots from Steinbach and INTEX are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Clean the pool robot thoroughly with clear water after each use. (Info: This removes chlorine and salt water residues - so the material is preserved for a long time and also does not fade as quickly).