Metall-EX liquid, 1,00 l
- Removes turbidities in the water and deposits on the fittings due to metals in the water
- Removes deposits on the pool bottom and walls
- Removes iron, copper and other metals
- Easy handling
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Metall-EX liquid, 1,00 l , UN1760
Removes metals and metal deposits from the water
USAGE: Cleaning agent. Metals belong to almost every water in more or less pronounced forms. A large number of metals cause either turbidity of water or deposits on the fittings. With Metall-EX liquid you can bond a major part of these metallic particles from the pool water and remove them with the help of the filter system. The use can be continued until your pool water is crystal clear.
For private swimming pools only.
DOSAGE: Before adding Metall-EX liquid, adjust pH-value to the optimal range of 7.0 - 7.4. When the pump is running, pour 0.3 - 0.6 l Metall-EX liquid per 10 m³ of water evenly near the inlet nozzles or over the water surface. Run the filter pump for at least 48 hours. Then, if possible, backwash the filter. Check the pH-value and correct if necessary. Metals and lime are crystallized, settle in the filter and can be removed by backwashing. Immediately after addition of Metall-EX liquid you can bathe again. Removing dry deposits: Leave a cloth impregnated with Metall-EX liquid for at least an hour on the spot. Metall-EX liquid dissolves the metal or lime from the substratum. Then simply wash off. Metall-EX liquid does not remove any organic deposits. Whether a deposit is metallic or organic is easy to determine: Hold a cloth moistened with Metall-EX liquid for 5-10 minutes directly on the stain. If the spot is brighter, it is mainly a metal deposit. If the stain changes yellow, an organic deposit is present, which can not be removed with Metall-EX liquid.
FAQs from category Pool cleaner:
Cause: Lime precipitates, not filtered particlesSolution: Adjust the pH level to 7.2 to 7.4 (by adding pH-Plus or pH-Minus). If there are suspended matters turn off the circulation pump and remove the flakes on the bottom with the pool cleaner after about 10-12 hours. Lime precipitates in the pool water (turbidity, shimmering white coating on the water surface, etc.) usually disappear shortly after adjusting the pH level and after the addition of a flocculants (while the filter system is running - WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Cause: Faulty filter function, too many organic substancesSolution: Backwashing. If the filter system is calcified, use an acidic filter cleaner. If the filter system is ok, make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l for a short time. The addition of flocculant is recommended as an additional measure (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Cause: Too little disinfectant in the water, algae growthSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Let the filter system run continuously during the first 1-2 days. For disinfection with chlorine: Wipe dead algae from the pool walls. Remove algae from bottom with a brush and an aspirator. Make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l. The addition of an algae protection is recommended. Backwash thoroughly. The added chlorine has degraded after a few days. Backwash thoroughly. If the water is not clear after 1-2 days, repeat the procedure. Cartridge filter system: Frequently clean or replace the cartridge. Alternatively, empty the pool completely, clean thoroughly and refill. After adjusting the pH value, treat the pool water with algicide to prevent new algae grow.
Cause: Iron deposits in the waterSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Add flocculant. (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!) Extend the filter runtime, backwash the filter system thoroughly. In the case of a cartridge filter system, clean the cartridge regularly and replace it if necessary.
Cause: Inadequate chlorine dosing, non-degraded organic substancesSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. After a shock chlorination up to ca. 3 mg/l this smell will disappear after a short time.
Cause: Inadequate chlorine dosing, non-degraded organic substancesSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. If there is too little chlorine in the water, increase the chlorine content. If the chlorine content is too high, reduce the dosage or drain the pool water and refill with fresh water. Again, pay attention to the pH value.
Take a bucket of warm water, add the required amount of chemical for your pool and stir well. Then empty the bucket with the mixture evenly into the pool with the filter system switched on (circulating).
The lid of our chemical articles also serves as a dosing aid.
Our chemistry must be equipped with a safety lock for the protection of children. This requires some strength to open.
Safety data sheets are stored with the respective chemical article on our homepage. If you still cannot find what you are looking for, please contact us via our form on helpdesk.steinbach.at.