- Rapid disinfection and oxidation of impurities without chlorine
- Well soluble compound
- Cleaves active oxygen in aqueous solution
- Switching from chlorine to active oxygen is possible at any time
- Field of application: initial dosing and long-term dosage
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Oxygen granules, 1,00 kg , UN3260
Granules for swimming pool disinfection without chlorine
USAGE: Water care product for disinfection and algae growth prevention. Granules for rapid disinfection and oxidation of impurities without chlorine. Well soluble compound, which cleaves active oxygen in aqueous solution. Switching from chlorine to active oxygen is possible at any time.
For private swimming pools only.
Only use a dosage floater, skimmer or dosage feeder.
DOSAGE: Before adding Oxygen granules, adjust pH-value to the optimal range of 7.0 - 7.4. The oxygen value should be between 5.0 und 10.0 mg/l. For initial dosage, 200g (ca. 200ml)/10m³ Oxygen granules and additionally 100-150ml/10m³ oxygen activator liquid. On a weekly basis, dissolve 100 g (ca. 100 ml) of oxygen granules per 10 m³ of water volume in water, add the mixture to the pool ideally via a skimmer and add 40-50 ml of liquid oxygen activator per 10 m³ of water volume to the pool near the inlet nozzles. In the case of cloudy water after frequent use, thundershower or high temperatures add 400g (ca. 400ml)/10m³ Oxygen granules to the pool water.
FAQs from category Active oxygen:
Cause: Lime precipitates, not filtered particlesSolution: Adjust the pH level to 7.2 to 7.4 (by adding pH-Plus or pH-Minus). If there are suspended matters turn off the circulation pump and remove the flakes on the bottom with the pool cleaner after about 10-12 hours. Lime precipitates in the pool water (turbidity, shimmering white coating on the water surface, etc.) usually disappear shortly after adjusting the pH level and after the addition of a flocculants (while the filter system is running - WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Cause: Faulty filter function, too many organic substancesSolution: Backwashing. If the filter system is calcified, use an acidic filter cleaner. If the filter system is ok, make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l for a short time. The addition of flocculant is recommended as an additional measure (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Cause: Too little disinfectant in the water, algae growthSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Let the filter system run continuously during the first 1-2 days. For disinfection with chlorine: Wipe dead algae from the pool walls. Remove algae from bottom with a brush and an aspirator. Make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l. The addition of an algae protection is recommended. Backwash thoroughly. The added chlorine has degraded after a few days. Backwash thoroughly. If the water is not clear after 1-2 days, repeat the procedure. Cartridge filter system: Frequently clean or replace the cartridge. Alternatively, empty the pool completely, clean thoroughly and refill. After adjusting the pH value, treat the pool water with algicide to prevent new algae grow.
Cause: Iron deposits in the waterSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Add flocculant. (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!) Extend the filter runtime, backwash the filter system thoroughly. In the case of a cartridge filter system, clean the cartridge regularly and replace it if necessary.
Cause: Inadequate chlorine dosing, non-degraded organic substancesSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. After a shock chlorination up to ca. 3 mg/l this smell will disappear after a short time.
Cause: Inadequate chlorine dosing, non-degraded organic substancesSolution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. If there is too little chlorine in the water, increase the chlorine content. If the chlorine content is too high, reduce the dosage or drain the pool water and refill with fresh water. Again, pay attention to the pH value.
Take a bucket of warm water, add the required amount of chemical for your pool and stir well. Then empty the bucket with the mixture evenly into the pool with the filter system switched on (circulating).
The lid of our chemical articles also serves as a dosing aid.
Our chemistry must be equipped with a safety lock for the protection of children. This requires some strength to open.
Safety data sheets are stored with the respective chemical article on our homepage. If you still cannot find what you are looking for, please contact us via our form on helpdesk.steinbach.at.