Auto Pool Cleaner ZX50

  • Automatic swimming pool cleaner for optimum pool bottom cleaning
  • Fine 0.3 mm mesh filter to catch even the finest dirt particles
  • 0.83 l collecting tray for dirt particles
  • 6.50 m long, torsion-free hose

Sold Out

The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.

including VAT
In stock
From € 49,- free shipping
Return free of charge

Product information

This compact suction side automatic pool cleaner is designed to efficiently clean your entire pool floor! Bringing the cleaning convenience previously reserved to only larger pools, this cleaner is ideal for smaller pools. With travel speed up to 5 meters per minute, this pool cleaner will swiftly get rid of debris in your pool, allowing you more time to swim and enjoy the pool.

Pool runner:
Operating mode: External pump connection
Cleaning area: floor cleaning
Suitable for saltwater: yes
Speed: 5 m/min
Water temperature: 10°C - 35°C
Ambient temperature: 10°C - 40°C
Pool size - floor area: 18 m²
Pump capacity external pump: 3.407 l/h - 5.678 l/h
Connection size: Ø 32/38 mm
Hose specification: Fixed length 650 cm

Free shipping
01 Reiniger Oberteil
including VAT
02 Schmutznetz
including VAT, plus shipping costs
03 Reiniger Unterteil
including VAT, plus shipping costs
04 Hose adapter
including VAT, plus shipping costs
05 O-ring for plug seal
including VAT, plus shipping costs
10 Schwimmkörper Schaumstoff
including VAT, plus shipping costs
11 Extension hose connector
including VAT, plus shipping costs

FAQs from category Pool robots:

Do not leave the cable in the pool all the time. After each use, remove it from the pool and unplug and turn off the cord. Wash the cable with clean water to remove chemical residues after each cleaning operation. Put the cable length into the pool according to pool dimensions, place the remaining cable at the pool edge, i.e. pull overflown cable out of the water. Place obstacles such as built-in pool ladders/installation ladders out of the pool to prevent the cable from getting caught.

Position the power supply so that the cleaner can easily reach all areas. Switch off the filter pump while cleaning with the pool vacuum. Enter the maximum possible length of the connection cable in the pool, but take into account a corresponding minimum distance between the control unit and the pool. Change the setting of the nozzles. 

Clean the filter container/filter bag and remove slippery debris such as algae from the pool walls. Put the pool vacuum cleaner into the pool at the optimum water temperature. This is between 10°C and 35°C. Check the drive belts and brushes for wear and replace them if necessary. Set the PH value correctly. This should be between 7.0 and 7.2. Switch off the unit and let all the air escape. Mount the additional buoyancy aids from the scope of delivery.

Check the plug of the power cord and the control unit or the battery. Plug the control unit directly into a socket and do not use extension cables. Check your house line for overload, the socket may be defective. Contact a qualified electrician.

There is air in the pool vacuum, switch off the unit, let all the air escape and let the pool vacuum sink to the ground. If necessary, adjust the salt content correctly.

Check the wheels/drive belts for wear and foreign objects in the drive. Replace the wheels/drive belts if necessary.

Check whether the water level in the pool is too high and drain the water if necessary. If your pool liner is a little rough, the pool vacuum will have more grip. Carry out a reduction of the buoyancy. If you have a salt water pool, the buoyancy is slightly higher in salt water; reduce the buoyancy.

It is necessary to weigh down the pool vacuum cleaner. A weight must be installed for this purpose. Please contact our Service Centre.

Our pool vacuums were designed for liner pools, the above materials have no grip or adhesion for the pool vacuum because the surfaces are too smooth.

Pull the cleaning hose and lift the automatic vacuum pool cleaner from the pool floor. The pool floor may be wrinkled, preventing the vacuum cleaner from moving. Check the water flow and make sure that the filter pump is switched on and has the appropriate power. Make sure that the gate valves are open. Clean or change the filter cartridge. For sand filter systems, you must backwash the filter.

You need to unblock or remove the cleaning lips because the sail, water outlet nozzle or cleaning lip may be stuck.

The buoyancy aids must be glued onto the inside of the upper part of the device - ideally offset and not directly next to each other.

The pool robot beeps when the ON/OFF button is pressed outside the water. This is due to the integrated water sensor. Put the pool robot into the water and after 15 seconds it will start cleaning the pool.

Press the ON/OFF button on the underside of the pool robot until you feel it click into place. If the ON/OFF button is pressed outside the water, the device beeps and does not switch on due to the integrated water sensor. Place the pool robot in the water. Please note: The pool robot only starts cleaning 15 seconds after it has been placed in the water.

All pool robots from Steinbach and INTEX are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Clean the pool robot thoroughly with clear water after each use. (Info: This removes chlorine and salt water residues - so the material is preserved for a long time and also does not fade as quickly).

Symbol photos

The pictures shown are just for reference, the actual product may differ.