Cart Cart

Auto Pool Cleaner - Floor cleaner only for INTEX Pools

  • Powerful Venturi principle cleaner for INTEX pools only
  • Pool hose Ø 38 mm, length 750 cm
  • Suitable for salt water
  • Very effective and hassle-free

Sold Out

The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.

Notifiy me:

including VAT

High performance floor vacuum for all INTEX pools Ø 38 mm screw connector and gate valve. Clean is carried out following the Venturi principle. Filter pump power of at least 5,678 l/h is required for optimal cleaning performance. The 750 cm long swimming pool hose (included in delivery) is connected directly onto the inlet (pressure side). The Auto Pool Cleaner from INTEX is also suitable for salt water.

Leistungsstarker Poolsauger arbeitet nach dem Venturi-Prinzip - nur für INTEX-Pools geeignet
Für eine optimale Reinigung wird eine Filterleistung von mindestens 6.056-13.248 l/h benötigt
Schwimmbadschlauch Ø 38 mm, Länge 650 cm, wird an der Einlaufdüse (druckseitig) angeschlossen
Für Salzwasser geeignet
Für alle INTEX-Aufstellpools mit Ø 38 mm Schlauchanschluss und Absperrschieber
Sehr effektiv und einfach zu bedienen

Top part of cleaner, including wheels
Required quantity for your set: 1
Screw fitting for top part
Required quantity for your set: 1
Gear module
Required quantity for your set: 1
Dirt net, as of 2014
Required quantity for your set: 1
Bottom part of cleaner
Required quantity for your set: 1
Micro screen
Required quantity for your set: 1
Hose adapter
Required quantity for your set: 1
Hose collar nut
Required quantity for your set: 2
Required quantity for your set: 1
Brush attachment A
Required quantity for your set: 4
Brush, H=32 mm
Required quantity for your set: 12
Brush attachment B
Required quantity for your set: 4
Plastic washer, Ø 74 x 8 mm
Required quantity for your set: 1
O-ring for plug seal
Required quantity for your set: 2

FAQs from category Pool robots:

The power cable gets tangled/twisted in the water, what can I do?

Do not leave the cable in the pool all the time. After each use, remove it from the pool and unplug and turn off the cord. Wash the cable with clean water to remove chemical residues after each cleaning operation. Put the cable length into the pool according to pool dimensions, place the remaining cable at the pool edge, i.e. pull overflown cable out of the water. Place obstacles such as built-in pool ladders/installation ladders out of the pool to prevent the cable from getting caught.

The pool vacuum does not reach all parts of the pool, what can I do?

Position the power supply so that the cleaner can easily reach all areas. Switch off the filter pump while cleaning with the pool vacuum. Enter the maximum possible length of the connection cable in the pool, but take into account a corresponding minimum distance between the control unit and the pool. Change the setting of the nozzles. 

The pool vacuum is not climbing the walls, what can I do?

Clean the filter container/filter bag and remove slippery debris such as algae from the pool walls. Put the pool vacuum cleaner into the pool at the optimum water temperature. This is between 10°C and 35°C. Check the drive belts and brushes for wear and replace them if necessary. Set the PH value correctly. This should be between 7.0 and 7.2. Switch off the unit and let all the air escape. Mount the additional buoyancy aids from the scope of delivery.

The cleaner shows no function, what can I do?

Check the plug of the power cord and the control unit or the battery. Plug the control unit directly into a socket and do not use extension cables. Check your house line for overload, the socket may be defective. Contact a qualified electrician.

The cleaner does not sink / emerges / turns in circles on the pool bottom, what can I do?

There is air in the pool vacuum, switch off the unit, let all the air escape and let the pool vacuum sink to the ground. If necessary, adjust the salt content correctly.

The cleaner does not move forward, what can I do?

Check the wheels/drive belts for wear and foreign objects in the drive. Replace the wheels/drive belts if necessary.

I have a salt water pool and the pool vacuum goes over the edge, what can I do?

Check whether the water level in the pool is too high and drain the water if necessary. If your pool liner is a little rough, the pool vacuum will have more grip. Carry out a reduction of the buoyancy. If you have a salt water pool, the buoyancy is slightly higher in salt water; reduce the buoyancy.

The pool vacuum cleaner only moves vertically in the pool, what can I do?

It is necessary to weigh down the pool vacuum cleaner. A weight must be installed for this purpose. Please contact our Service Centre.

I have a stainless steel or tiled pool

Our pool vacuums were designed for liner pools, the above materials have no grip or adhesion for the pool vacuum because the surfaces are too smooth.

What do I do if the INTEX automatic vacuum pool cleaner does not move or moves very slowly?

Pull the cleaning hose and lift the automatic vacuum pool cleaner from the pool floor. The pool floor may be wrinkled, preventing the vacuum cleaner from moving. Check the water flow and make sure that the filter pump is switched on and has the appropriate power. Make sure that the gate valves are open. Clean or change the filter cartridge. For sand filter systems, you must backwash the filter.

The device does not turn on the pool wall, what can I do?

You need to unblock or remove the cleaning lips because the sail, water outlet nozzle or cleaning lip may be stuck.

Important information

Only suitable for INTEX above ground pools with Ø 38 mm hose connection and gate valve. - Not suitable for built-in pools!

Symbol photos

The pictures shown are just for reference, the actual product may differ.