Steinbach
Pool cleanser super, 1,00 l
- For the cleaning of heavy lime deposits
- Dissolves rust, urine deposits and general dirt
- For indoor and outdoor pools
- Perfect for basic cleaning
Sold Out
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Product information
Strongly acidic basic cleanser for the main- and the spring-cleaning of swimming pools, dissolves limescale
Pool cleanser super, 1,00 l, UN3264, Met. Corr. 1, Skin Corr. 1B, Eye Dam. 1, STOT SE 3
USAGE: Cleaning agent. Pool cleanser super serves for the basic cleaning in spring and dissolves heavy lime deposits, rust and general dirt. For outdoor and indoor use. After use the cleanser must be carefully removed. The cleanser is phenol- and formaldehyde-free
For private swimming pools only.
DOSAGE: Depending on the degree of contamination, apply 1:100 / 1:10 to undiluted with brush or scrubber. Allow to react for at least 10 to 15 minutes. After treatment wash area thoroughly with plenty of water. On fittings apply min. 1: 100 diluted and do not leave longer than 15 minutes. To increase the cleaning effect, use warm water. After cleaning, rinse thoroughly with water. Do not apply in direct sunlight.
FAQs from category Pool cleaner:
Cause: Lime precipitates, not filtered particles
Solution: Adjust the pH level to 7.2 to 7.4 (by adding pH-Plus or pH-Minus). If there are suspended matters turn off the circulation pump and remove the flakes on the bottom with the pool cleaner after about 10-12 hours. Lime precipitates in the pool water (turbidity, shimmering white coating on the water surface, etc.) usually disappear shortly after adjusting the pH level and after the addition of a flocculants (while the filter system is running - WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Possible Causes: Faulty filter function, too many organic substances
Solution: Backwashing. If the filter system is calcified, use an acidic filter cleaner. If the filter system is ok, make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l for a short time. The addition of flocculant is recommended as an additional measure (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!). Backwash thoroughly. Clean cartridge filter or replace by a new one.
Possible cause: Too little disinfectant in the water, algae growth
Solution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Let the filter system run continuously during the first 1-2 days. For disinfection with chlorine: Wipe dead algae from the pool walls. Remove algae from bottom with a brush and an aspirator. Make a shock chlorination, meaning raise the chlorine level of the pool water up to 3 mg/l. The addition of an algae protection is recommended. Backwash thoroughly. The added chlorine has degraded after a few days. Backwash thoroughly. If the water is not clear after 1-2 days, repeat the procedure. Cartridge filter system: Frequently clean or replace the cartridge. Alternatively, empty the pool completely, clean thoroughly and refill. After adjusting the pH value, treat the pool water with algicide to prevent new algae grow.
Possible cause: Iron deposits in the water
Solution: Adjust the pH level to 7.2 to 7.4 by adding pH-Plus or pH-Minus. Add flocculant. (WARNING: prohibited with cartridge filter systems and filter balls; the filter can stick!) Extend the filter runtime, backwash the filter system thoroughly. In the case of a cartridge filter system, clean the cartridge regularly and replace it if necessary.
Possible cause: Inadequate chlorine dosing, non-degraded organic substances
Solution: Adjust the pH level to 7.0 to 7.4 by adding pH-Plus or pH-Minus. After a shock chlorination up to ca. 3 mg/l this smell will disappear after a short time.
Possible cause: Inadequate chlorine dosing, non-degraded organic substances
Solution: Adjust the pH level to 7.0 to 7.4 by adding pH-Plus or pH-Minus. If there is too little chlorine in the water, increase the chlorine content. If the chlorine content is too high, reduce the dosage or drain the pool water and refill with fresh water. Again, pay attention to the pH value.
Take a bucket of warm water, add the required amount of chemical for your pool and stir well. Then empty the bucket with the mixture evenly into the pool with the filter system switched on (circulating).
The lid of our chemical articles also serves as a dosing aid.
Our chemistry must be equipped with a safety lock for the protection of children. This requires some strength to open.
Safety data sheets are stored with the respective chemical article on our homepage. If you still cannot find what you are looking for, please contact us via our form on our helpdesk.