At Steinbach you will find a wide range of lengths of all commercially available ribbed swimming pool hoses with a diameter of 32 mm or 38 mm for installation and attachment parts. The respective ends of the hose are either sleeved or with internal thread. Auxiliary materials for connecting hoses such as hose nozzles, hose clamps, adapters for INTEX pools, T-piece nozzles, gate valves as well as 3-way valves and much more can be found in our product range. Hose connections for all commercially available ribbed swimming pool hoses usually have a diameter of 38 mm. 32 mm connections as well as hoses can be found mainly in your products from INTEX.
from €5.99including VAT, plus shipping costs
€24.90including VAT, plus shipping costs
€17.90including VAT, plus shipping costs
€8.99including VAT, plus shipping costs
€19.90including VAT, plus shipping costs
€4.99including VAT, plus shipping costs
€10.90including VAT, plus shipping costs
€9.99including VAT, plus shipping costs
Free shipping€49.90including VAT
Free shipping€179.00including VAT
Frequently asked questions for Hoses:
Yes, but note that the hose must be cut straight, deburred and cleaned. In addition, more glue has to be applied. It is easier with the appropriate adapter screw connection.
This is not intended. There are sufficient possibilities to create transitions, the parts required for this are listed in our brochure ("Individual components Styrofoam pools").
It is best to use our 2" double nipples (art.no. 062085) - Please note that you also need flat gaskets for sealing (art.no. 0409331).
This can sometimes happen due to production reasons; please refer to our notes in the operating instructions. Weak dripping is best eliminated by wrapping Teflon tape over the affected connections.
This is due to the fact that the seals are lubricated inside with a lubricant - on the one hand for sealing and on the other hand so that the components can be adjusted more easily (plastic on plastic). After the first couple of turns, the lever will turn smoothly.
Pool hoses in aisle sizes
32 or 38 mm hoses are used for various purposes in your swimming pool for piping: you can connect your filter system, skimmer, vacuum cleaner as well as corner and edge brushes, pool heaters and much more to your pool with a suitable hose.
Make sure that the hose connection and the diameter of the hose are the same. This means: a 32 mm hose connection requires a 32 mm hose, a 38 mm hose connection requires a 38 mm hose. With special adapters you can also use a 32 mm hose from INTEX with a 38 mm diameter connection.
The swimming pool hoses offered by Steinbach as well as all accessories can be used for swimming pools with chlorine as well as with salt for water disinfection.
What to do in case of leaks
The cause of damage and thus leaks can be manifold: For example, the connection to the hose may have become permeable or bathers may unintentionally introduce small, pointed objects into the pool, causing cracks or similar in the hose.
If you notice that water is leaking, first make sure you have the correct hose size for your connections of any kind. This affects many areas of your pool: Connecting hoses are used in pool technology for sand and cartridge filter systems, pool heating and pool accessories such as vacuum cleaners, pool brushes and other cleaning equipment.
If there is a leak at the connection, you can use a Teflon tape to seal the screw connections again. If necessary, use hose clamps to tighten the connections. If the hose is torn, it is advisable to replace it with a new one to avoid water damage and energy loss.
Swimming pool hose plastic, 32 mm sleeved
The multi-function swimming pool hose from Steinbach is available with a diameter of 32 mm in one or more sections from 1.10 m length and a fixed length of 6.6 m.
The two ends of the hose are sleeved for optimum fastening.
The hose is flexible and is suitable for both chlorine and salt water pools.
Tip: Hose clamps for 32 mm diameter hoses ensure a firm connection.
Swimming pool hose plastic, 38 mm sleeved
The multifunctional swimming pool hose with a diameter of 38 mm can be supplied in one or more sections of 1.50 m or with fixed lengths of 6 m, 7.6 m or 9 m. You can easily connect the 1.10 m or 1.50 m long hoses for pool piping to meet your individual requirements.
The two ends of the hose are sleeved for optimum fastening. The hose is flexible and suitable for both chlorine and saltwater pools.
Tip: Hose clamps for hoses with a diameter of 38 mm ensure a secure, firm connection.
Swimming pool hose INTEX 32 mm
The swimming pool hose from INTEX with 32 mm diameter and a fixed length of 150 cm is universally applicable and suitable for all chlorine- and salt-based above-ground-pools. Sleeved, reinforced ends serve for secure fastening.
Swimming pool hose INTEX 38 mm
The INTEX swimming pool hose with 38 mm diameter at a fixed length of 150 cm is suitable for all INTEX pools. A screw connection on both sides with 2'' internal thread is used. The hose can be used for both chlorine and salt water pools. Note: For INTEX pools with 32 mm connections you need an adapter.
Accessories for swimming pool hose - hose clamps
The hose clamps are used for a tight connection and can be used for swimming pool hoses with 32 mm as well as 38 mm diameter. Hose clamps are available from Steinbach as a double pack or as a pack of 4 pieces.
Double hose nozzle diameter 38 mm/38 mm
The double hose nozzle is used to connect two 38 mm x 38 mm hoses. The hose nozzle can be used for swimming pools with chlorine and salt water. Included in delivery is a double pack of hose nozzles for 38 mm swimming pool hoses.
Double hose nozzle diameter 32/32 mm
The double hose nozzle is used to connect two hoses with a diameter of 32 mm each. The hose nozzle can be used for swimming pools with chlorine and salt water. Included in delivery is a double pack of hose nozzles for 32 mm hoses.
Hose nozzle Ø 38mm/adhesive, OD 50
The hose nozzle can be used with a 38 mm diameter swimming pool hose and has an adhesive connection with an outer diameter of 50 mm (OD 50). Included in the delivery is a double pack of hose nozzle Ø 38mm/adhesive, OD 50.
Hose nozzle Ø 32/38mm x 1 1/2" AG
The hose nozzle is used for the connection during pool piping and can be used with a 32 mm or 38 mm diameter swimming pool hose and has a 1 1/2 inch external thread. Included in delivery is a Teflon tape for a secure, tight connection and a double pack of hose nozzles.
T-piece nozzle Ø32/38mm
The T-shaped grommet made of high-quality plastic is used to connect swimming pool hoses with a diameter of 32 mm or 38 mm. The T-shaped nozzle can be used for pools with chlorine and salt water.
3-way valve Ø 32/38 mm
The 3-way valve is used for targeted water flow when using a pool heater, heat pumps and solar collectors or solar mats. Swimming pool hoses with a diameter of 32 mm or 38 mm can be connected to the 3-way valve.
Connection set Ø 32 mm - compatible with water revitalisation
The complete set is suitable for all INTEX pools with a hose connection of 32 mm. Included in delivery are 2 pieces of feed-throughs, 2 pieces of sealing caps, 1 inlet nozzle and 1 screen grid
Shut-off valve Ø 38 mm x 1 1/2" AG
The shut-off valve is used to completely interrupt the water flow. It is made of high-quality plastic and has a 38 mm hose connection and a 1 1/2" external thread. The gate valve can be used for chlorine and salt water pools.
Adapter for swimming pool hoses - Retracted adapter B
The INTEX special adapter is made of high quality plastic and is suitable for tight connection of the filter unit type ECO with INTEX swimming pool hoses with a diameter of 38 mm and 2 inch thread as well as INTEX pools with a diameter of 32 mm with hose connection and gate valve with 2 inch thread.
The special adapter can be used for both chlorine and salt water pools.
Adapter for INTEX Pools/Steinbach 2 "AG x 1 "IG
The special adapter made of high quality plastic is used for pressure side connection of Steinbach filter systems and INTEX Pools with 2 inch thread connection with 1 inch internal thread. It is ready for use with chlorine and salt water pools.
Adapter A, Ø32/38mm x 2“IG
The special adapter is 9.2 cm long and made of high-quality plastic. It is used to connect a hose with 32 or 38 mm diameter without 2" internal thread with a 2" connection and is suitable for many INTEX products. The adapter thus enables a secure hold.
Adapter for INTEX Pools 2" x 1 1/2" AG
The special adapter is used to connect Steinbach filter systems and INTEX Pools with 2 inch thread connection to 1 1/2 inch external thread. The adapter is simply screwed on tightly and offers a secure, tight hold.