Cart Cart

For a short time only: Pool set including all accessories for just € 199.90 SHOP NOW

Pipes

PVC pipes and fittings can be easily assembled to form pool piping for chlorine and salt water pools. Various elbows, sockets, nipples, T-pieces, drain valves, ball valves, bypass sets, check valves or gate valves are suitable fittings for controlling the water flow.

Fittings with an external diameter of 50 mm (OD 50) are generally used for private pools. Plastic pipes and adhesive fittings are used for targeted water flow, to interrupt the water flow and to drain the water. The PVC used is strong, durable and suitable for pools with chlorine and salt water.

Items 1-12 of 42

Page
per page
Set Descending Direction

Items 1-12 of 42

Page
per page
Set Descending Direction

 


Pool Piping: Cleaning and Bonding Instructions

Special PVC cleaners and adhesives are required to join PVC pipes and the matching PVC fittings.

Before cleaning and bonding, the pipes must be cut vertically to the desired size. Please use only suitable tools.

The PVC cleaner is used to clean the pipes and fittings before gluing, so that the adhesive has a proper adhesion. Apply the cleaner with a brush or rag. Then join the pipes or fittings to be glued together with a special PVC adhesive. Apply the adhesive evenly and do not turn the parts to be joined during the gluing process. Please note that the areas to be glued must be dry and the adhesive should not be used at temperatures below 5 degrees.

After only a few seconds the parts are connected and sealed. Remove excess adhesive. The drying time varies, but is usually 1 hour. A drying time of 24 hours is recommended before using the glued pipes, fittings and the like.

Please note the safety advice that PVC solvent and PVC adhesive are highly flammable. Cleaning as well as gluing should only be done in a well ventilated place. Use protective goggles and a breathing mask during processing. Store the PVC solvent and PVC adhesive in a dry and frost-proof place with good ventilation and without direct sunlight.


Bypass set

The bypass set made of high-quality plastic is suitable for use with external heating systems such as a heat pump or solar heating systems of any kind such as solar collectors, solar mats and similar.

The complete bypass set can be used for a swimming pool hose with a diameter of 32 or 38 mm and includes a 3-way valve with which you can control the water flow in a targeted manner, as well as switch on and off, hose nozzles including hose clamps, Teflon tape and 1 T-piece.


PVC ball valve

 The ball valve is made of high quality plastic and can be used for pools based on chlorine and salt water. You can stop the water flow with the ball valve, which is often also called a stop valve. The designation PN 10 refers to the nominal pressure, which must not exceed 10 bar. The outer diameter is 50 mm (DA 50).


PVC drain valve

The drain valve is used to drain water and is made of high-quality plastic. It has a 3/4 inch external thread (AG 3/4") and an internal diameter of 16 mm (NW 16).


PVC check valve

The PVC check valve, made of high quality plastic, is used to direct the water flow in one direction during pool piping and is suitable for pools with chlorine and salt water. The designation PN 16 refers to the nominal pressure, which must not exceed 16 bar. The outer diameter is 50 mm (DA 50).


PVC elbow 90 degrees

The 90 degree PVC elbow made of high quality plastic for chlorine and salt water pools serves as a connecting piece of hoses and is simply glued. The nominal pressure must not exceed 10 bar (PN 10). The outer diameter is 50 mm (DA 50).


PVC elbow 45 degrees

The 45 degree PVC elbow made of high quality plastic for chlorine and salt water pools serves as a connecting piece of hoses and is simply glued. The nominal pressure must not exceed 10 bar (PN 10). The outer diameter is 50 mm (DA 50).


PVC T-piece

The T-piece made of high-quality PVC is a fitting for targeted water flow. The permissible operating pressure may be 10 bar (PN 10), the outer diameter is 50 mm (DA 50).


PVC reduction angle 90 degrees

The 90 degree reduction angle is made of high-quality plastic, is suitable for pools with chlorine or salt water and can be glued quickly. The permissible operating pressure may be 16 bar (PN 16), the outer diameters are 40/50 x 50 mm.


PVC sleeve

The PVC sleeve for chlorine and salt water pools is used to join PVC pipes together. The permissible working pressure may be 10 bar (PN 10), the outer diameter is 50 mm (DA 50).


PVC insert with thread

The PVC insert has an outer diameter of 50 mm (OD 50) with a 3/4 inch inside thread (3/4") and can be used for pools with chlorine and salt water.


PVC screw connection gluing sleeve x gluing sleeve

 A sleeve can be glued to the PVC screw connection at both ends. It consists of high-quality plastic and is suitable for both chlorine and salt water pools. The permissible operating pressure may be 16 bar (PN 16), the outer diameter is 50 mm (DA 50).


PVC transition sleeve nipple glued sleeve x AG

 The PVC transition sleeve nipple has an outer diameter of 50 mm (OD 50) with a 2 inch female thread (2") and can be used for swimming pools based on chlorine and salt water. The nominal pressure must not exceed 10 bar (PN 10).


PVC transition sleeve nipple glued socket x AG

The PVC transition sleeve nipple is used as a connecting piece to the pool piping and has an external diameter of 50 mm (OD 50) with a 1 1/2 inch internal thread (1 1/2"). The maximum operating pressure is 10 bar (PN 10). The PVC transition sleeve nipple can be used for chlorine-based and saltwater-based pools.


PVC transition screw connection adhesive sleeve x male thread

The PVC transition screw connection adhesive sleeve with external thread is made of high quality plastic and is both chlorine and salt water resistant. An O-ring is included in the scope of delivery. The permissible nominal pressure may be 16 bar (PN 16), the outside diameter is 50 mm (OD 50) with a 1 1/2 inch external thread (1 1/2 “).


PVC adhesive hose

The adhesive hose made of high-quality PVC is used for pool piping and is simply glued together. The hose has an outer diameter of 50 mm (OD 50). The product consists of a roll of 25 m.


PVC transition fitting sleeve for PVC adhesive hose

The PVC transition fitting sleeve is suitable for the Steinbach PVC adhesive hose and is made of high-quality plastic. The PVC transition union can be used for swimming pools with chlorine and salt water. Technical data: d 50 clamp x 50 mm (outer diameter) adhesive socket.


PVC transition screw joint glued sleeve x IG

The PVC transition screw joint glued sleeve with internal thread is made of high-quality plastic and is resistant to both chlorine and salt water. The admissible nominal pressure may be 16 bar (PN 16), the outer diameter is 40/50 mm with a 1 1/2 inch female thread (1 1/2").


PVC transition fitting IG for adhesive PVC hose

The PVC transition fitting IG is suitable for the adhesive PVC hose from Steinbach for pool piping and is made of high-quality plastic. The PVC transition fitting can be used for pools with chlorine and salt water. Technical data: d 50 clamp x 1 1/2 inch internal thread.


PVC transition fitting AG for adhesive PVC hose

The PVC transition fitting AG is suitable for the adhesive PVC hose from Steinbach and is made of high-quality plastic. The PVC transition fitting can be used for swimming pools with chlorine and salt water. Technical data: d 50 clamp x 1 1/2 inch external thread.


PVC transition angle 90 degrees for PVC adhesive hose

The PVC transition angle 90 degrees is suitable for the PVC adhesive hose from Steinbach and consists of high-quality plastic. The angle can be used for swimming pools with chlorine and salt water. Technical data: DA 50 (50 mm outer diameter) x d 50 clamp.


PVC pool pipe

The PVC pipe is made of high-quality plastic and is suitable for both chlorine and saltwater pools. The permissible nominal pressure may be 10 bar (PN 16), the outer diameter is 50 mm (DA 50). The pipe is offered by Steinbach at 2 metres each.


Pipe clamp

The pipe clamp made of high-quality plastic is suitable for PVC pipes with an external diameter of 50 mm (OD 50) and can be used for swimming pools with chlorine and salt water.